JL Audio
MX600/3
600W RMS 3-Channel Amplifier

$499.99
JL Audio MX600/3
JL Audio MX600/3 JL Audio MX600/3 JL Audio MX600/3 JL Audio MX600/3 JL Audio MX600/3 JL Audio MX600/3

Overview

Engineered specifically for powersports applications, the 3-channel MX600/3 amplifier employs our high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum housing is highly resistant to corrosion, with an IPX7 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.

Generating a potent 75W x 2 into 4 ohms, plus a solid 400 watts for a subwoofer system, the MX600/3 makes a great all-in-one solution for driving a complete audio system from a single, ultra-compact chassis.

Onboard filters include a 12 dB / octave high-pass crossover on the main channels and a dedicated 24 dB / octave low-pass crossover for the subwoofer channel. Other features include a bass boost EQ, variable infrasonic filter and subwoofer output polarity switch. A dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.

This amplifier features a rugged powder-coated finish, a gasketed cover for the controls and stainless steel hardware for durability.

NexD™ Switching Technology

NexD™ amplifier technologies produce exceptional audio quality, unsurpassed total efficiency and high power from very compact amplifier designs.

Beginning with the original 'Slash' subwoofer amplifiers, JL Audio has been at the forefront of Class D amplifier design. Our NexD™ switching technology stems from our Class D expertise to deliver outstanding fidelity and efficiency, leading to compact amplifiers that deliver high power and exceptional value.

Let's get a little nerdy... A traditional PWM switching amp design uses a fixed switching frequency and varies the pulse width based solely on the audio input signal to the pulse modulator. This basic approach assumes some ideal conditions, like a rock-steady power supply, that do not necessarily occur in a real, in-car installation. Power supply sag with signal causes distortion at all power levels with these designs, even well below clipping. The cure for this is feedback (a corrective signal sent back to the input side), but this becomes impractical as the audio frequency increases, making it a good solution for band-limited (subwoofer) amps, but not for full-range amplifiers.

Taking the above into account when designing the NexD™ subwoofer amplifiers, we have taken the simple fixed PWM approach and enhanced it with a very high switching frequency: 240 kHz, which is about 4x higher than most Class D subwoofer amplifiers. This pushes the amplifier's bandwidth to at least 500 Hz with minimal distortion and improves efficiency, while keeping typically bulky circuity more compact. Your subwoofers will reward you with tight, rock-solid bass performance.

For the full-range NexD™ amplifiers and channels we applied a variable, ultra-high speed version of the NexD™ technology (switching at well over 400 kHz). In these designs, a self-oscillating modulator with "feed-forward" sends information about the instantaneous power supply voltage to the modulator, combining this with the input signal to cancel out any distortion due to supply voltage fluctuation. This reduces distortion prior to applying feedback, simplifying the overall feedback loop design.

The bottom line is simply great audio: clean, powerful and reliable.

Differential-Balanced Inputs

JL Audio’s Differential-Balanced Inputs are engineered to combat induced cable noise, which is a common problem in car and marine audio installations. This technology allows for the use of conventional RCA cables, while delivering many of the benefits of a true balanced connection and accepting a wide range of input signal levels.

Today’s vehicles are equipped with sophisticated electronics capable of generating noise and interference that can intrude into the audio path, ruining the listening experience.

Most audio equipment uses single-ended, ground-referenced RCA jacks to receive audio signals. This means that the RCA shield is connected directly to signal ground. This is a simple, cost effective input design that works well for short runs in noise free environments. In noisier environments, this method cannot reject the common mode noise that could be on both RCA conductors (shield and center conductor).

By having more than one chassis-grounded RCA shield on a device, single-ended input designs are also more susceptible to ground loops. If noise is present on both conductors while the shield is connected to ground, the input amplifier will amplify the noise relative to the grounded RCA shield. When there are multiple RCA connections or any other conductors subjected to a magnetic field, this will cause a difference in potential across the RCA loop to be amplified at the grounded RCA as noise (a classic ground loop).

JL Audio’s Differential-Balanced Input circuits measure the center pin of the RCA connection relative to the RCA shield, even when the shield is not connected to ground, and even when the voltages at both conductors are moving relative to ground. Because both the center conductor and the shield see high impedance to ground at the input, a ground loop cannot be formed, as there is no current flow to induce a voltage as noise.

This works equally well with differential-balanced, or unbalanced signal sources, making this input architecture compatible with all standard car and marine audio equipment, using standard, unshielded, twisted-pair RCA cables. No special cables are required, unlike the fully balanced connections used in professional audio.

Another benefit of the Differential-Balanced Input design is that it easily accepts low-level and high-level signals from a variety of factory head unit outputs and amplifiers, including single ended “ground referenced” sources, as well as Balanced or Unbalanced “Bridged or BTL” sources. This eliminates the need for Line Output Converters (LOCs) in most installation scenarios.

The obvious question is: “Why don’t all car audio amplifiers use Differential-Balanced Inputs?” The answer is simple: it costs more. Executing a proper differential-balanced input section requires more components and better quality components than a basic single-ended design, so you generally won’t find them on less expensive amplifiers.

Specifications

Rated Continuous (RMS) Power @ 14.4V
Main Channels: 75W RMS x 2 @ 4Ω
Main Channels: 100W RMS x 2 @ 2Ω
Main Channels: 200W RMS x 1 @ Bridged @ 4Ω
Subwoofer Channel: 250 W RMS x 1 @ 4Ω
Subwoofer Channel: 300 W RMS x 1 @ 3Ω
Subwoofer Channel: 400 W RMS x 1 @ 2Ω
Subwoofer Channel: N/A @ 1.5Ω
Rated Continuous (RMS) Power @ 12.5V
Main Channels: 50W RMS x 2 @ 4Ω
Main Channels: 80W RMS x 2 @ 2Ω
Main Channels: 100W RMS x 1 @ Bridged @ 4Ω
Subwoofer Channel: 200 W RMS x 1 @ 4Ω
Subwoofer Channel: 250 W RMS x 1 @ 3Ω
Subwoofer Channel: 300 W RMS x 1 @ 2Ω
Subwoofer Channel: N/A @ 1.5Ω
Frequency Response
20 Hz - 20 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power
>88 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W
>68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4Ω
>92 / 50 Hz
Damping Factor @ 2Ω
>43 / 50 Hz
THD+N @ Rated Power (Main Channels)
<1% @ 2Ω per Channel
THD+N @ Rated Power (Subwoofer Channels)
<1% @ 2Ω per Channel
Input Voltage Range @ RCA Inputs
Switchable from 250 mV - 4 V RMS (Low) to 580 mV - 14 V RMS (High)
Min. Copper Power / Ground Wire Gauge
4 AWG Wire
Fuse Rating
60 A (AFS, AGU or MaxiFuse™)
Filter Slope(s)
12 dB/octave
Filter Frequency Range: Channels 1 & 2 (Front)
35 Hz - 300 Hz
Filter Frequency Range: Subwoofer Channel
40 Hz - 400 Hz
Filter Mode(s): Channels 1 & 2 (Front)
High-Pass Only
Filter Mode(s): Subwoofer Channel
Low-Pass Only
Detented, Calibrated Filter Freq. Potentiometer
Yes
Filter Defeat Function
Yes
Remote Subwoofer Level Control
Optional (RBC-1)
Remote Level Modes
N/A
Channel Input Mode Switch
Yes (2/4 Channel)
Pass-Through Preamp Output
None
Source Channel Selection for Pre-Outs
N/A
Height (H)
1.77” / 45 mm
Width (W)
9.33” / 237 mm
Depth (D)
4.5” / 115 mm
Net Weight
N/A
More Information
Brand JL Audio
Amplifier Class Class D
RMS Power 600W RMS
RMS Power per Channel at 2 Ohms 100W RMS x 2 @ 2 Ohms
Sub Channel RMS Power at 2 Ohms 400W RMS x 1 @ 2 Ohms
Sub Channel RMS Power at 4 Ohms 250W RMS x 1 @ 4 Ohms